Darex XT-3000 attachments manual (LEX050) Manual do Utilizador descarregar pdf

Congratulations on the purchase of your Darex

XT-3000 Large Drill Attachment. (21 mm—30

mm) As part of the assembly (see picture from

left to right) you should have a SA16565XA Large

drill alignment, SA16575CA Sharpening fixture,

and SA16500TA Large Drill Chuck.

By now you are familiar with the ‘quick disconnect’

feature of your XT-3000. Start by placing the

Large Drill Alignment on the top of your XT-

3000. Rotate the ‘Docking Lever’ clockwise to

securely lock the fixture in place. In a similar

manner, remove your current sharpening fixture

and replace it with the Large Drill Sharpening

Fixture.

Now would be a great

time to determine the

point angle of the drill

that is to be sharpened

and adjust both the

sharpening fixture and

alignment to that point

angle. The Sharpening

fixture is adjusted by

pulling the red lever

towards (counter

clockwise) the operator

and sliding the fixture to

the point angle desired. Lock the fixture by

returning the red lever to its original position. The

alignment is adjusted by

rotating the black lever

located at on the front of the

alignment fixture. As per the

decal, rotating the lever

towards the operator will

reduce the amount of relief

ground onto the drill and

pushing the lever away from

the operator will increase the relief. Placing the

pin at the midway point on the decal is a good

starting place for 118° drills. For 135°-150° drills

start with the alignment 2 marks towards the

operator. You can set the alignment at any setting

necessary to achieve the amount of relief desired.

Place the drill in the chuck and turn the chuck

knob clockwise until the drill slides freely through

the chuck jaws. Next slide the Chuck and drill into

the alignment rotating the chuck until one of the

‘cam dogs’ aligns with the

mating ‘notch’ in the fixture.

You will notice the opposite

‘dog’ aligns with a reference

mark machined into the

alignment fixture.

Now push the drill through the chuck until it

contacts the stop. Rotate the drill clockwise until

Large Drill Attachment

LEX050

Incorrect Correct

1 2 3 4 5 6 ... 18 19

Resumo do Conteúdo

Página 1 - Large Drill Attachment

41 Congratulations on the purchase of your Darex XT-3000 Large Drill Attachment. (21 mm—30 mm) As part of the assembly (see picture from left to rig

Página 2

50 Counter Sink Attachment LEX150 SA16823TA Alignment Assembly PP16823TF Alignment Thumb Screw PP16820BF Alignment Arm PP16312FF 1/8"x2&

Página 3

51 Congratulations on the purchase of the Darex XT-3000 Brad point Attachment. (LEX200) This attachment consists of 2 pieces, 1 Sharpening Fixture, SA

Página 4

52 Brad Point Attachment Brad Point Attachment LEX200 SA11790PA PP11745FF 1/4-20 x 1 SSS PP11790PF Point angle lock knob PP16652TF F

Página 5 - XY Table Attachment

53 Congratulations on the purchase of your Darex XT- 3000 Step Drill Attachment. (LEX250). This attachment consists of 3 pieces, 1 Sharpening Fixture

Página 6

54 Rotate the Chuck until 1 of the alignment dogs rests firmly against the Alignment. Rotate the Pawl Locating Cam until the arrow lines up to the ma

Página 7 - Countersink Instructions

55 Step Drill Attachment

Página 8

56 Step Drill Attachment SA16950BA SA16652TA Feed Bearing Assembly PP16652TF Feed Bearing Bolt PP08560LF Bearing SA03413BA Pawl Assembly PP0

Página 9 - Countersink Attachment

57 Congratulations on the purchase of your Darex XT-3000 90°-120° Sharpening Attachment. As part of the assembly you should have a Sharpening fixture

Página 10

58 90º - 120º Sharpening Attachment

Página 11 - BRAD POINT ATTACHMENT

59 90°- 120º Attachment SA16652TA Feed Bearing Assembly PP16652TF Feed Bearing Bolt PP08560LF Bearing SA16615BA Pivot Lock Lever Assembly P

Página 12 - Brad Point Attachment

42 the outer edge of the cutting lip is touching the pins in the setting fixture. Firmly tighten the chuck by turning the knob clockwise while the chu

Página 13 - LEX 250

43 Large Drill Attachment

Página 14

44 Large Drill Attachment LEX050 SA16615BA Pivot Lock Lever Assembly PP16615BF Pivot lock lever PP16630FF 5mmX8mm SSS SA16585TA Timing Adjuste

Página 15 - Step Drill Attachment

45 XY Table Attachment X-Y Table No Sub Assemblies, Send in for Repair

Página 16 - Step Drill 3mm-12mm Chuck

Página 17 - 90º - 120º Drill Attachment

47 Congratulations on the purchase of your Darex XT-3000 Countersink Attachment. This fixture comes with 2 V-40 double angle collets and is used in co

Página 18

48 To sharpen the tool, determine which angle the tool will be sharpened at. To adjust the X-Y table, loosen the Pivot Lock Knob and swing the table t

Página 19 - 90°- 120º Attachment

49 Countersink Attachment

Comentários a estes Manuais

Sem comentários

Darex XT-3000 attachments manual (LEX050) Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Ferramentas elétricas Darex XT-3000 attachments manual (LEX050). Darex XT-3000 attachments manual (LEX050) User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Ferramentas elétricas Darex XT-3000 attachments manual (LEX050)