Darex XPS-16 SCHEMATICS & WORK INSTRUCTIONS Manual do Utilizador

User Manual Page 1 SERVICE PARTS REPLACEMENT SCHEMATICS & WORK INSTRUCTIONS USER SECTION CHUCK SWING CASTING ASSEMBLY EXPLODED VIEW: SA12500

User Manual Page 10 Removing and Replacing the Nema Drive Gear Refer to the Chuck Spindle Drive Belt Replacement instructions for cover, chuck and be

User Manual Page 11 Removing and Replacing the Rotate Sensor 1. Remove the 3, 3mm button head screws with a 2mm Allen wrench and remove the cover plat

User Manual Page 12 4. With a small flat blade screw driver, reach down and pull the solenoid lock pin back out of the locking hole. Rotate the chuck

User Manual Page 13 Removing and Replacing the A-Axis (Swing) Sensor Removing and Replacing the A-Axis (Swing) Sensor 1. Locate the marked swing sens

User Manual Page 14

User Manual Page 15 CHUCK ASSEMBLY SA12505TA

User Manual Page 16

User Manual Page 17 Removing and Replacing Diameter Detect Rod Refer to the Chuck Spindle Drive Belt Replacement instructions for cover and chuck remo

User Manual Page 18

User Manual Page 19 ELECTRICAL WIRING DIAGRAM SA12150EF

User Manual Page 2

User Manual Page 20

User Manual Page 21 Removing and Replacing the Cooling Fan Removing the Cooling Fan 1. Remove the 2 screws holding the panel to the machine. 2. Swing

User Manual Page 22 7. Disconnect the 2 sets of red and black wires that go to a connector above the fan on the back board. Repla

User Manual Page 23 Removing and Replacing the LCD Display Removing and Replacing the LCD Display 1. Remove the screws on the door support and top c

User Manual Page 24 6. Remove the 7, ¼” acorn nuts from the LCD. Note: One is inaccessible and has no nut. Slide the LCD out. 1. To replace the

User Manual Page 25 Removing and Replacing Switches Removing and Replacing The E-Stop, Cycle Start and Feed Hold Switches To remove the power switche

User Manual Page 26 3. Securing the switch in place is a plastic nut at the base of the threads. Use needle nose pli-ers to remove the nut and slide t

User Manual Page 27 GRIND MOTOR ASSEMBLY SA12640MA

User Manual Page 28

User Manual Page 29 1. Turn the machine on. 2. Push the check icon. 3. Push the tool icon. Removing and Replacing Grind Motor Assembly 4. Push the bel

User Manual Page 3 CHUCK SWING CASTING ASSEMBLY SA12500CA

User Manual Page 30 8. Remove the 4 screws and washers holding the motor in place. 9. Slide the motor down the slotted bracket and out of the machine

User Manual Page 31 Removing and Replacing Grind Motor Belt 1. Turn the machine on and push check. 2. Push the tool icon. 3. Push the belt icon in upp

User Manual Page 32 Removing and Replacing Grind Motor Brushes 1. Refer to Removing and Replacing Grind Motor Assembly instructions to remove and repl

User Manual Page 33 SPINDLE CARTRIDGE ASSEMBLY SA12615TA

User Manual Page 34

User Manual Page 35 Removing and Replacing the Spindle Arbor Cartridge Assembly Removing and Replacing the Spindle Arbor Car-tridge Assembly. 1. Ref

User Manual Page 36 7. Loosen the 2, 3mm set screws in the top of the cartridge block that holds the cartridge in place. 8. Slide the cartridge forwar

User Manual Page 37 1. Reinstall the wheel. 2. Reinstall the wheel cover. 3. Refer to Grind Motor Belt Replacement to in-stall and set proper tension

User Manual Page 4

User Manual Page 5 Removing and Replacing the Chuck Spindle Drive Belt 1. Remove the 3, 3mm button head screws with a 2mm Allen wrench and remove the

User Manual Page 6 4. To loosen and remove belt, insert a flat blade screw driver in the slotted bearing screw. 5. On the back of the casting is a 4

User Manual Page 7 Replace Chuck Spindle Drive Belt 1. Take the knob and jaw assembly and position all jaws in slots. Holding in your hand, align the

User Manual Page 8 Removing and Replacing the Chuck Belt Idler Assembly Refer to the Chuck Spindle Drive Belt Replacement instructions for cover and c

User Manual Page 9 Removing and Replacing the Chuck Locking Solenoid Refer to the Chuck Spindle Drive Belt Replacement instructions for cover and chuc